223 subsonic with clays powder11/22/2023 ![]() USE THIS DATA WITH ALLIANT BRAND POWDERS ONLY. ![]() The individual accessing this site assumes the risk of safe loading practices.įailure to do so could result in severe personal injury (or death) and/or property damage. Alliant Powder neither assumes nor authorizes any person to assume for it any liability in connection with the use of any product or data. Buyers and users assume all risk, responsibility and liability whatsoever for any and all injuries (including death), losses or damages to persons or property (including consequential damages), arising from the use of any product or data, whether or not occasioned by seller's negligence or based on strict liability or principles of indemnity or contribution. Never substitute any smokeless powder for Black Powder or its substitute.Īlliant Powder expressly disclaims any and all warranties with respect to any and all products sold or distributed by it, the safety or suitability thereof, or the results obtained including, without limitation, any implied warranty of merchantability or fitness for a particular purpose and/or any other warranty. Only problem is, I can’t find it anywhere due to the current situation. Anyway, my buddy uses accurate 1680 and I’ve shot some of his loads and works great. You would think a powder that’s designed around the 300 black out would meter better. Never mix any two powders regardless of type, brand, or source. CFE Black is a joke and a terrible powder. Having done the research I have found that most mild loads use cast projectiles but I would rather continue and use my usual projectile, a Hornady 55gn Soft point. Along the lines of a 22 mag or Hornet load. ![]() This information and data may vary considerably depending on many factors, including the components used, component assembly, the type of firearm used, reloading techniques, safety precautions practiced, etc. I have a 223 and have been thinking of developing a mild load for areas where distance is shortish and noise is an issue. there wont be any leading at 900 fps.The information displayed on this site, including ballistic data, was derived from tightly controlled laboratory conditions. i would also use cast bullets why spend money on expensive jacketed bullets when you can cast your own for free. i have seen safe loads from the 223 to the 45-70. 2gr Hodgdon Clays, seated to the cannelure. that said fil a case 2/3 of the way and this is your load. 223 subsonic) using small charges of Titegroup pistol powder. Would anyone know what the maximun powder charge of trail boss in a 223 behind a 55 grain bullet wold be?ĭo not compress trail boss. I also load subsonics with up to a 77 grain bullet using these powders. Look at Clays or 700X for a powder and use 3-3.5 grains are you are set. .223 sized brass (trimmed to length) SRP (in my case 41 CCI) 62gr SS109 bullets 5.2gr Trail Boss (fills case nicely - does not meter to well though donut shaped powder) OAL - 2.255 I shot these out of a AR15 w/ 1-7 twist 10.5' barrel / AAC can (these would be excellent on a suppressed bolt action. You can use a jacketed bullet and I would never waste my time with a lead one. while not subsonic i use a reduced load of 8 grains of unique and a 40 grain bullet. Here is a quick guide to help you get started. All these powders are appropriate in the listed loads. i have seen it but don't remember the charge weight. The Hodgdon Reloading Data Center (RDC) lists 21 different powder types that can be used in the. I think you can get it done with a cast bullet and trailboss powder. The other portion of this question is put located here. I think I know the answer to this and that is.Īnyway anyone have any thoughts or suggestions? I know that the Hogdon reloading data center does show a load with Clays powder using 4 grains but this is specifically for a 1 and 12 twist barrel. 223 rounds to shoot through a suppressed AR with a 1 and 9 twist.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |